Brugsanvisning PANASONIC NVVX9B

[. . . ] Refer servicing to qualified service personnel. CAUTION Unit ≥ Do not place sources of naked flames, such as lighted candles, on this unit. ≥ This unit may receive radio interference caused by mobile telephones during use. If such interference occurs, please increase separation between this unit and the mobile telephone. ≥ This unit is intended for use in moderate climates. Placement ≥ Place this unit on an even surface. [. . . ] Dolby Virtual Speaker and 3D surround effects are turned off. The setting is maintained until it is changed again. ≥ To turn off Dolby Virtual Speaker and the 3D surround effects, select “STEREO” as the sound mode. ( right) ≥ To turn off the 3D surround and the Clear-mode dialog effects, refer to “Using the Dolby Virtual Speaker effect”. ( 33) 30 RQT9849 SC-HTB770_RQT9849-B_mst. book 31 ページ ２０１３年２月２５日　月曜日　午前１１時５３分 Linked operations with the TV (VIERA Link “HDAVI ControlTM”) What is VIERA Link “HDAVI Control”? VIERA Link “HDAVI Control” is a convenient function that offers linked operations of this system, and a Panasonic TV (VIERA) under “HDAVI Control”. You can use this function by connecting the equipment with an HDMI cable. See the operating instructions for connected equipment for operational details. What you can do with VIERA Link “HDAVI Control” To make sure that the audio is output from this system, turn the main unit on by using the TV’s remote control and selecting home cinema from the speaker menu of VIERA Link menu. The availability and function of the settings may vary depending on the TV. Refer to the operating instructions for the TV for details. Preparation 1 Confirm that the HDMI connection has been made. ( 25, 26) 2 Set the “HDAVI Control” operations on the connected equipment (e. g. , TV). 3 For the optimal “HDAVI Control” operations change the following settings on the connected TV*1. 4 Turn on all “HDAVI Control” compatible equipment and select the TV’s input for this system so that the “HDAVI Control” function works properly. 5 If a device is connected to the HDMI IN terminal, start play to check that the picture is displayed on the TV correctly. ≥ Make sure that a Bluetooth® device is already paired with this system. ( 28) Press and hold [MUTE] for more than 4 sec. “STANDARD” indicator blinks (A): Main (Factory preset) “STEREO” indicator blinks (B): Secondary (SAP: Secondary Audio Program) When A and B both blink: Main and secondary Press [ ] to select “ ”. ≥ “ ” indicator will blink slowly. If the indicator lights, a Bluetooth® device is already connected with this system. ( 28) Press [ ] to display the current mode. “STANDARD” indicator blinks: MODE1 (Factory preset) Emphasis on connectivity “STEREO” indicator blinks: MODE2 Emphasis on audio quality While the setting is displayed, press [MUTE] to change the setting. ≥ The setting changes each time [MUTE] is pressed. ≥ The indicator for the selected setting blinks for 20 sec and then exits the setting mode. ≥ The setting is maintained until it is changed again. While the mode is displayed, press [ ] to select the mode. ≥ The setting changes each time [ ] is pressed. ≥ The indicator for the selected setting blinks for 10 sec and then exits the setting mode. ≥ The setting is maintained until it is changed again. 32 RQT9849 SC-HTB770_RQT9849-B_mst. book 33 ページ ２０１３年２月２５日　月曜日　午前１１時５３分 Using the Dolby Virtual Speaker effect Depending on your preference, It is possible to turn off the 3D surround effect and the clearmode dialog effect. Auto standby function With this function turned on, this unit can be set to automatically switch to standby mode if there is no signal input and no operation is performed for 2 hours. While pressing and holding [SOUND] on the remote control, press and hold [VOL r] on the main unit for more than 4 sec. “STANDARD” indicator blinks: 3D surround effect and clear-mode dialog effect is on. “STEREO” indicator blinks: 3D surround effect and clear-mode dialog effect is off. While pressing and holding [DIALOG LEVEL j] on the remote control, press and hold [INPUT SELECTOR] on the main unit for more than 4 sec. ≥ The indicator for the current setting blinks for 20 sec. “STANDARD” indicator blinks: Auto standby function is on. “STEREO” indicator blinks: Auto standby function is off. While the setting is displayed, press [SOUND] to change the setting. ≥ The setting changes each time [SOUND] is pressed. ≥ The indicator for the selected setting blinks for 20 sec and then exits the setting mode. [. . . ] The product is warranted for 12 months from the date of purchase. Subject to the conditions of this warranty Panasonic or its Authorised Service Centre will perform necessary service on the product without charge for parts or labour, if in the opinion of Panasonic, the product is found to be faulty within the warranty period. This warranty only applies to Panasonic products purchased in Australia and sold by Panasonic Australia or its Authorised Distributors or Dealers and only where the products are used and serviced within Australia or it's territories. Warranty cover only applies to service carried out by a Panasonic Authorised Service Centre and only if valid proof of purchase is presented when warranty service is requested. [. . . ]