Brugsanvisning AEG-ELECTROLUX DD8692-M

[. . . ] Mit dem Warndreieck und/oder durch Signalwörter (Warnung!, Vorsicht!, Achtung!) sind Hinweise hervorgehoben, die für Ihre Sicherheit oder für die Funktionsfähigkeit des Gerätes wichtig sind. Dieses Zeichen leitet Sie Schritt für Schritt beim Bedienen des Gerätes. …… Nach diesem Zeichen erhalten Sie ergänzende Informationen zur Bedienung und praktischen Anwendung des Gerätes. Mit dem Kleeblatt sind Hinweise zum wirtschaftlichen und umweltschonenden Einsatz des Gerätes gekennzeichnet. [. . . ] Attention: in recirculation type hoods the V1 Motor LED may start to flash as well as the Speed + V3 LED. This indicates that as well as replacing the activated charcoal filter, it is also necessary to perform maintenance operations on the metal grease filters (see paragraph Metal grease Filter). 38 S07_06 Instructions for use • • • • • Replacing Take off the metal grease filter and remove the activated charcoal filter from its housing by turning the clips provided. Fit the new activated charcoal filter and replace the metal grease filter. Enabling the alarm signal S07_31 In recirculation type hoods the saturated filters alarm must be enabled as indicated below: Turn off the lights L and the Suction Motor V1; Press and hold the button V3 for at least 10 seconds, until the Leds start to flash. Note the number of flashes: - 2 flashes of the LED Activated charcoal filter saturation alarm ENABLED - 1 flash of the LED Activated charcoal filter saturation alarm DISABLED Resetting the alarm signal To turn the alarm signal off, proceed as follows: - Press the button V3 for at least 3 seconds, until the Leds flash in confirmation. In any case the saturated filters alarm will only come into operation when the suction motor is turned on. ATTENTION - There could be a possible fire hazard if the filters are not replaced according to these instructions. Lighting 1 - It consists of 2 20 W-halogen spotlights. 2 - Replacement Remove the two screws that lock the metal ring, take the spotlight out of its holder by pulling slightly. When replacing, make sure that both pins are well inserted in the holder seat. Special accessories Wall housing MKZ 125 External dimensions Wall aperture Outlet duct ABS 120 Ø 120 mm aluminium Outlet duct ABS 125 Ø 125 mm aluminium Serial no. 610 899 004 Height x width in mm 250 x 220 185 x 210 Serial no. 942 118 612 S07_28 39 Instructions for use Installation Instructions Safety warnings for the electrician Electrical connection Voltage 230 V ~ Connect using: a fixed power cable with a Schuko plug (European type) or a fixed connection (by an authorised electrician). Using a Ø 8 mm drill bit, drill the points marked in this way. b) When installed with the air outlet A08_05 directed towards the wall (fig. 4a), it 4a 4b 4c will be necessary to drill an air ducting opening, measuring Ø120 or 125 mm, according to the diameter of the flange F provided. 50 ø1 Z 7 ø1 2 0 X 44 650 40 18 Installation a) b) c) a) b) c) d) e) 2 - Fitting the fixing elements Insert the rawl plugs provided into holes 1 and 2. Fix the wall bracket S in hole 2 using the screw V provided (fig. 6). 3 - Fitting the hood canopy C to the wall O Remove the metal grease filter (see the paragraph on Maintenance). 6 Fit the support rod B using the two screws K (3, 5x9, 5) provided (fig. S Hook the hood canopy C to the eye bolts O fixed in holes 1 (fig. Adjust the support rod B so that it pushes against the wall V 4 mm (fig. There are two adjustable hooks 5 1 A08_06 2 A08_07 7 K B 8 O O A08_08 S07 _09 O • • • • at the rear of the hood, which can be used to adjust its position as follows: Turn the screws L until the position of screws N coincides with the lower access holes. Turn the screws N to adjust the vertical and horizontal position of the hood. Lock the screws L to fasten the hood against the wall. Insert the plugs T provided in the holes giving access N to screws N. A08_10 B 9 L Installation of the chimney A No matter which type of installation is being used, any wooden shelves in the area where the hood is to be fitted must first be removed, drilled and later replaced. [. . . ] A08_23 b) verwijder het eventuele koolstoffilter dat in de wasemkap aanwezig is (zie Onderhoud). 2 - Filterende aansluiting Kan alleen worden uitgevoerd als de luchtuitgang naar boven is gericht. Monteer het gerichte rooster G op de luchtuitgang (afb. Het koolstoffilter in de wasemkap moet worden aangebracht nadat de elektrische aansluiting tot stand is gebracht. Filterende aansluiting of aansluiting met afvoer van de lucht naar buiten E E E 21 22 Q A08_24 Q Elektrische aansluiting en controle van de werking 1 - De onder punt 3. 2, 3. 3 en 3. 4 van paragraaf 3, aangegeven waarschuwingen betreffende de veiligheid, moeten nauwgezet in acht worden genomen. [. . . ]